Cb0178-12 load data.

7/8 1,200fps Rem 209P e3 WAA12L 16gr 7,265 psi. Alliant 3/4oz loads list only Extra Lite And CB lists no e3 loads for their CB0175-12 wads. I would prefer to use my abundant CB0175-12's rather trying to get proper stack with CB0178-12 wads while simply lowering the shot drop. The pressures above seem pretty low and would suggest that an e3 load ...Clay Dot loads to same weight as Clays recipes in 12 gauge shotshells. Used the Claybuster gray (CB0178-12) for thousands of 7/8 ounce loads, and with pink (CB0175-12) wads I've loaded a ton of 3/4 ounce cowboy loads with 14 to 15 grains of Clay Dot. I myself "recommend" it. No published data recommends it as far as I know.Using AAHS hulls, Winchester 209 primers, 17.5 grains Clays behind a CB0178-12 wad and +-380 grains no. 8 hard shot, I'm getting around 1200 fps. This morning, I chronographed some of the same loads with 18 grains Clays, and got between 1330 and 1350 fps. I hope this helps. I wasn't looking for a bunker load, but I sure found one.You can look through their reloading information online, they have quite a few recipes. Think all use the CB0178 (WAA12L) wad. Less powder required than even Red Dot, nice high pressures, everyone seems to be happy with cleanliness. ... look at the Winchester and Remington hull specific data and 3/4 and 7/8 Oz loads are listed. 12-Gauge, 2 3/4 ...Buy Shotshell Reloading Equipment online: SportsmansReloads carries a full line of Shotshell Reloading Equipment & Components from all the major brands. Skip to content Total: $ 0.00. ... Claybuster Shotshell Wads 12 Gauge CB0178-12 (Replaces WAA12L) 7/8 oz $ 10.99 - $ 124.99. In stock. Select options. Add to wishlist.

Since there are numerous listed loads for Red Dot, select one you like and go with it. Personally I like using all the components you listed, using 17.3 to 17.5 grs. Promo Wads can be Clear Duster, CB0178-12, or DR XXl-1 pink. Any one of these will work. DLMInstead I used the WAA12L gray wad, (actually the CB0178 -12 Clone wad), and it worked and fit fine. Pressures are so low, 7,800 PSI, that it burns very dirty, but it breaks targets just fine. ... The same peak pressure load data with Red Dot will get you considerably slower MV and use quite a bit less powder. That implies a considerably faster ...

Currently I use this wad( CB0178-12) for 3/4 oz loads with good results and just want to make a few boxes with 1 oz. Tim. Patience is a waste of time. ...CB0178-12 (gray) wad Rem. STS or Win. 209 primer Right around 1200 fps at pressure less than 8,200 psi This is the 12 gauge load I use mostly. If one loads it with #8-1/2 or #8 shot, it makes a good non-handicap trap load. Remington STS-type hulls or Winchester AA (I use AA hulls for this load) 1 ounce shot 17 grs. Titewad

Never let it be said that I can't take a hint. My favorite CAS 12 Gauge load is 4.3CC (about 66 grains) of Schuetzen FFg, a 1/8" Circle Fly Over Powder wad, a 1/2" Circle Fly Compression wad, 1 1/8 ounces of #8 shot, a Circle Fly Over Shot Card, a Winchester 209 Primer, all stuffed into a Remington STS hull.You really have 3 choices for great fit with 7/8 oz. loads. CB0178-12 Claybuster Clear Duster, (I like this one best) DR XXL-7/8 (Pink) Down Range wad ... So much so, that with the advent of the new Claybuster CB0175-12, I don't even buy 7/8th's wads any more (the grey CB0178-12's).The reloading data is not much different using Clays (approximately 19.4 - 19.8 grains), 1 oz, winchester 209 and remington hulls, can I load 1 ounce using the CB0178-12? Has anyone reloaded Remington gund clubs using the CB0178-12 wad and 1 ounce?So the whole load data is the Remington 12 gauge STS or Gun Club hulls, Winchester 209 primers, 24 Grains of Hi-Skor 800x powder, ClayBuster CB0178-12 wads which are replacements for the WAA12L, 1/8" thick Nitro Card (x2) in the wad cup, then the 7/8oz Lee Key Drive slug on top of the nitro cards, finished off with a factory 8-point crimp.Oct 21, 2010 · Since i shoot 7/8 oz for practice, and 1 oz for shoots, and the availability of the CB0178-12 is better, I'd live to be able to standardize everything but the charge bar. Since the CB1100-12 doesn't crimp nearly as well for the 7/8 oz loads, naturally, it'd be more advantageous to use the other wad, if the pressures were safe.

One of my favorite 3/4oz loads uses Claydot: Blue Rio hull. Rio 209 primer. Claydot, 19.0 grains. CB-0175-12 wad. Reload 2-3 times then pitch hulls. As long as you can get decent crimps, most hulls (except for Federal Gold Medal) will work with the CB-0175-12 wad without any filler such as Cheerios, Rice, etc.

Claybuster Wads CB0178-12 Intended as an economical wad replacement for name brand wads, Claybuster wads are ideal for target and wing shooters. Made with 100% prime resin for consistency with every loaded shell. The CB0178-12 wad was designed for use in 7/8 oz to 1 oz trap, skeet, or sporting clays loads. Replaces the Winchester WAA12L

Detailed Description. Claybuster CB6114-12 (500/bag) Claybuster is a great American manufacturing partner. They utilize quality virgin materials in their wads and they are made here in the USA. Quality, value, and service that dusts the competition! The CB6114-12 is a terrific field wad for straight-wall hulls.STS Hull--F209-A primer--17.5 Green Dot--CB0178 grey wad--and 7/8 of of your choice. This load is a great skeet load when loaded with 9s amd a great 16 yd trap load when loaded with 8s. ... you mean our version of the TGT-12". That really set me back a bit, because I see no similarity and the TGT-12 is marginal, at best, for any 7/8 loads. Save ... Larry from Cookeville, TN. I have been loading the CB0178-12 with 13/16 oz. (by volume) and find it to be an outstanding load. Show More Testimonials. To receive additional information: J-Ron, Inc. [email protected]. Customer Service: 800-922-6287. 635 Bob Posey Street. Henderson, KY 42420. Ramshot HUNTER. A double-base, clean burning, high performance propellant that is perfect for elk country cartridges such as the 270 Winchester, 300 WSM and 338 Win Mag. It's the only spherical powder in the popular 4350 burn range making it an ideal powder for a wide range of cartridges. The excellent flow characteristics allow accurate ...I've been loading a 7/8 oz skeet load with 17.7 gr of Competition, CB4100-12b or CB0178-12 wads and Cheddite primers. I've been happy with the performance. Velocity around 1250 and 7,500 psi for the CB0178-12 wad. No published data for a 7/8 oz load with the Windjammer clone wad (4100-12b) but if anything the pressure would be lower.Buy Waa12l 12 Gauge Shotshell Wads CB0178-12: GunBroker is the largest seller of Other Reloading Supplies Reloading Supplies Ammunition Reloading All: 1040768947 Advancedrhett1977. 3227 posts · Joined 2004. #8 · Apr 16, 2012. Any powder that will give you light recoiling loads if you use less powder. Keep the speeds lower and you have less recoil. AA Lite will give you 980fps. That's the softest shooting 7/8oz load I've ever shot. Artificial intelligence is no match for natural stupidity.

Sep 23, 2011 · 17.5gr of Red Dot, 7/8 oz of #8 1/2 shot, CB0178-12 gray wads, and Fiocchi primers in Gun Club hulls. Out of my Citori XT these are easy on the shoulder and bust clays just fine from the 16 yard line. I'll be using CB0178-12 for the light loads (3/4oz), but have not settled on a 1 1/8 oz wad yet. I am primarily shooting sporting clays, and possibly doves once in awhile. ... But since I am pushing the high side of the load data I think I'll weigh each one for 600 yds. I might switch to 1oz loads for clay, but for now I'll probably throw an 1 ...CB0175-12 (3/4 oz. Wad) For use in 3/4 oz. skeet, sporting clays or hunting loads. Versatile for most hulls depending on powder volume. Optimum load is 3/4 oz. Featuring Lead-in Taper . CB0178-12 (WAA12L) For use in 7/8 to 1 oz. trap, skeet or sporting clay loads. Performs best in tapered hulls, Remington or Winchester. Optimum load is 7/8 oz.Low recoil 12 ga. loads using Titewad powder: Winchester AA 2 3/4" hull or equivalent. Winchester WAA12L (gray) wad or Claybuster CB0 178-12. Winchester 209 Primer. 14.2 GR Titewad. Use #20 MEC Bushing. 7/8 ounce of #8 shot. This recipe was shared with me several years ago. I have used it with good success.3/4 oz. 12 ga. Loads with e3. I searched the reloading section and found Case's light 3/4 oz. load. There was a comment in the string from Case that said you could use any 12 ga. powder, and using a published 7/8 oz. recipe for that powder, drop a grain or two. I currently use 16.2 gr. of e3 with a 7/8 oz. load, so I would have to drop down to ...

The CB0178-12 wad was designed for use in 7/8 oz to 1 oz trap, skeet, or sporting clays loads. Technical Information: •Replaces the Winchester WAA12L •Optimal Load: 7/8 oz •Intended as an economical wad replacement for target and wing shooters •Wads are made with 100% prime resin for consistency These are the best wads to use for ...Shotshell Reloading Press: $96.98. $66.12 increase decrease. Add to cart. Add to wishlist. Compare product. Email a friend. Availability: In stock. Products specifications. ... 12 GA 7/8 OZ Gray CB0178-12 743491001780. Claybuster Shotshell Wads - 12 GA 7/8 OZ Gray $19.42 $11.91. Add to cart Add to compare list Add to wishlist.

Detailed Description. Claybuster CB0118-12 WT Promo wads (500/bag) The Claybuster wad line is an economical wad line built for target-shooters and wing-shooters alike. With twenty-five different models from which to choose, the Claybuster wad line can satisfy nearly every target or wing shooting application for reloading.Buy Claybuster Shotshell Wads 12 Gauge CB0178-12 (Replaces WAA12L) 7/8 oz Online. Intended as an economical wad replacement for name brand wads, Claybuster wads are ideal for target and wing shooters. Made with 100% prime resin for consistency with every loaded shell. The CB0178-12 wad was designed for use in 7/8 oz to 1 oz trap, skeet, or sporting clays loads.CB4118-12B Reloading Data ~ Windjammer Tournament Wad. J-Ron Inc.'s Claybuster Wad Line is a well established economical wad line built for target-shooters and wing-shooters alike. With twenty-one different models from which to choose, the Claybuster Wad Line can satisfy nearly every target or wing shooting application for reloading.CB 1075-20 Reloading Data ~ 3/4 Ounce Shot Loads. J-Ron Inc.'s Claybuster Wad Line is a well established economical wad line built for target-shooters and wing-shooters alike. With twenty-one different models from which to choose, the Claybuster Wad Line can satisfy nearly every target or wing shooting application for reloading.With 700X powder I think you will need a CB0178-12 wad or a WAA12L wad for 7/8 oz loads in Rem Nitro or STS hulls. 700X doesn't take up as much space as some powders like Clays, Red Dot or Clay dot. With the load data you posted I would load at least 17.0 gr of 700X in both the 7/8 oz and 1 oz loads. We need to know what hulls you plan on using ...For International-style loads use 20.0 Red Dot/Promo under the CB0178-12 with 24gm or 7/8 oz shot, freakin' killer load. ... Clays and International powders with same score results. We have also used DR12 wads for one oz shot loads but 1 oz loads do not cycle well in the Benelli but work fine in the 1100 and CZ. Save Share. Like. M. mudpack.Gender:Male. Location:S.W. PA. Interests:NRA Life. SASS# 76982. Logans Ferry Regulators, Tusco Longriders, Posted June 29, 2022. I need some 12ga 7/8 oz light cowboy load data for Clays, Clay Dot, Promo, and or Red Dot. I just came into a MEC 600jr but only a few large bushings.12 gauge. CLAYBUSTER WAD 12ga 7/8oz (WAA12L) 5000/CS. Quantity: Add to Cart. Share this! Read 14 Reviews. Product Information. For use in 7/8 to 1 oz. trap, skeet or …point is, i have no loading data as tightwad didn't exist then, you might have to consult them, you may have to buy one of their manuals to find the data you're looking for---i also show no data for that wad. ... WAA12L or CB0178-12 wad W209 or Remington primer Oehler Model 35 chronograph results: Average velocity: 1210 High velocity: 1229 …

CB 1075-20 Reloading Data ~ 3/4 Ounce Shot Loads. J-Ron Inc.'s Claybuster Wad Line is a well established economical wad line built for target-shooters and wing-shooters alike. With twenty-one different models from which to choose, the Claybuster Wad Line can satisfy nearly every target or wing shooting application for reloading.

Claybuster 0178 7/8 oz wads. I use these to load 24 gram shotshells (slightly lighter than 7/8 oz). Using Remington STS hulls and xx.x grains of Clay Dot powder produces about 1310 fps and 7800 psi. This is a very light recoil load that powders sporting clays targets out as far as 70 yards (with the right chokes).

This pilot for Sun Country Airlines was caught trying to bring a loaded gun on a flight, and was promptly arrested at the TSA checkpoint. It turns out that flight crews are just as...For instance CB8100-12 has the figure 8. That will require the thin features in the crush area to either be burnt or cut with an .050" endmill to a depth of .250. Both add costs. If you look at the CB0178-12, it's designed such that all of the thin web sections are created by shear walls or kiss offs... Much cheaper.Nor is there any load data on the hogdon site. Does anyone have any load data for this powder for 12 gauge. the bottle has a load data on the front shows this only. ... AAHS, ANY REMINGTON HULL - CB0178-12, Downrange XXL Pink, Gray AA12L; FEDERAL, IMPORT HULL - CB2100-12, Downrange XXL Orange, Fed. 12S0. Those wads satisfy dimensions required ...OK, the load data that Hodgdon gave you should have specified a wad. If they were talking Winchester, the WAA12L is gray and, and CB equivalent is the gray wad CB0178-12 If they suggested the WAAA12SL, which is pink, the CB equivalent is CB1100-12. Also pink. Normally, those 2 gray wads work best with 7/8 ounce shot.CB0175-12 ( 3/4 oz. Wad) For use in 3/4 oz. skeet, sporting clays or hunting loads. Versatile for most hulls depending on powder volume. Optimum load is 3/4 oz. Featuring Lead-in Taper. CB0178-12 (WAA12L) For use in 7/8 to 1 oz. trap, skeet or sporting clay loads. Performs best in tapered hulls, Remington or Winchester.3/4 oz. 12 ga. Loads with e3. I searched the reloading section and found Case's light 3/4 oz. load. There was a comment in the string from Case that said you could use any 12 ga. powder, and using a published 7/8 oz. recipe for that powder, drop a grain or two. I currently use 16.2 gr. of e3 with a 7/8 oz. load, so I would have to drop down to ...Claybuster CB0178-12 wad ... SASS Wire is a WHOLE LOT more fun now with reloading data. RRR Okay, don't know if anyone was planning to check back on Red Dot and IMR Red comparison. Shot 13.4 gr. Red Dot left barrel and 14.4 gr. IMR Red right barrel in my S x S 12 g., 6 stages (loaded all with #25 bushing). Maybe an occasional …

Since 1932, more 100 straights than any other powder. America's number one choice. Lot-to-lot consistency. Economical and efficient. Principal Purpose: Light and standard 12 ga. target loads. Secondary Uses: Handgun loads. Remarks: The number one premium clay target powder, now 50 percent cleaner. Canister Sizes:[email protected]. Customer Service: 800-922-6287. 635 Bob Posey Street. Henderson, KY 42420. Harvester Muzzleloading. Tweets by @CBWads. J-Ron Inc.'s Claybuster Wad Line is a well established economical wad line built for target-shooters and wing-shooters alike. With twenty-one different models from which to choose, the Claybuster ...Federal Gold Medal Plastic. Win 209. 700x (16 gr) Claybuster CB0178-12 wad (WAA12L) 7/8 oz lead #7.5. My goal is to get a load that is as comfortable as possible for my daughter shooting for her high school trap team. She's fairly petite and the store bought shells seem to pound on her. Right now she's shooting 1145 fps 1 oz loads.Instagram:https://instagram. restoration hardware outlet san diego cadoes wells fargo have a daily withdrawal limitrooster tractor supplyst lucie humane society florida 4th. down. 2354 posts · Joined 2004. #10 · Oct 4, 2012. lesharris said: I have used about 3500 of the CB-6100-12 wads in Federal,Fiocchi,and several other hulls. Using data supplied with the wads, Claydot powder,1oz. loads. All loaded and shot well. Yes I missed some targets but I miss with factory loads also.I've already checked load data form Hodgdon (my original load vs the same load with CB111-12) which indicates all is safe, legal etc. etc. Pressure actually decreases slightly. ... The CB1118-12 has proven itself for over 20 years to be an excellent alternative to the WAA12. Stop all the hand wringing and just use the wad as presented. firefly guitar reviewscraigslist reading pa apartments The CB0178-12 wad was designed for use in 7/8 oz to 1 oz trap, skeet, or sporting clays loads. Technical Information: •Replaces the Winchester WAA12L •Optimal Load: 7/8 oz •Intended as an economical wad replacement for target and wing shooters •Wads are made with 100% prime resin for consistency These are the best wads to use for ...The reason for my interest in the clear duster is that it looks to have a shorter shot cup than the CB0178 grey wad. Both Claybusters CB0178 & CB1100 have the same size shot cup, the CB0178 has longer legs. ... I have already loaded almost 2 flats with 1 oz loads in pink CB1100-12 Wads and they worked perfectly. I just got started with the ... jessica ditzel Looking for some help with load data. I'm using 45 colts in my rifle and 45 cowboy specials in my pistols. Using 180gr cast boolits. The easy thing to do is fill the case with powder. But I think it's going to cause unnecessary recoil/smoke/noise. My typical 12ga loads are 12-12.5grs Promo, CB0178-12 grey clay buster wad, and 7/8oz shot in ...Since i shoot 7/8 oz for practice, and 1 oz for shoots, and the availability of the CB0178-12 is better, I'd live to be able to standardize everything but the charge bar. Since the CB1100-12 doesn't crimp nearly as well for the 7/8 oz loads, naturally, it'd be more advantageous to use the other wad, if the pressures were safe.